Gemini UP-1000, Universal Interior Water-Borne Primer, White, Gallon
Gemini's Universal Water-Borne White Primer, UP-1000 is a single component waterborne primer designed to dry fast and have excellent sanding properties. It has been designed for finishing interior cabinetry and woodwork, and may be top-coated with specific, approved, waterborne and solvent-borne products. For wood substrates only. For interior use only.
- Interior
- Water-borne
- Primer
- Wood substrates only
- Fast-drying
- Spray application
| Type | 1K Primer |
|---|---|
| Size | Gallon |
| Color | White |
| Brand | Gemini |
| Series/Sub-Brand | Gemini |
| Color Family | White |
| Material | Water-Borne |
| Manufacturer Code | UP-1000-1 |
Application Method: If using this system over oil based stains- A test panel for adhesion checks must be prepared and adhesion with the system you intend to use should be verified before proceeding. Recommended application is with a Medium T-Bar applicator or brush. This material may be sprayed as well. Always measure the moisture content of the wood. Sand floors using accepted NOFMA/MFMA procedures.
Edge out 6 inches from the baseboard or wall with a paint pad or polyester brush. Stay within 2-3 feet of the puddle line to avoid lap marks, streaking, or thicker film build. Be sure to feather edges. Starting from the head wall, pour a 4 inch wide line of finish the length of the floor going with the grain. Stop about 3 feet from the opposite wall. Hold applicator at a slight angle and dcloth it in a “squeegee” or “plowing” type motion to move the puddle from one side of the room to the other.
Overlap 2 inches of the previous pass and pull parallel passes until the entire floor is coated. Brush out all turns, stops, and other applicator marks in the same direction as the puddle line. Add finish to the puddle line when needed to maintain a wet edge across the room. When you are 2-3 feet from existing wall, begin to taper the puddle line down to a nickel sized bead. Allow each coat a minimum of 40 minutes to level.
After the finish levels, place fans in an adjacent area to pull moisture away from the job site. When each coat has dried a minimum of 2-3 hours, re-check moisture content. If moisture content is not equal to the first reading, allow more time before proceeding to the next coat.
This product must not be polluted with oil, solvent-based paint or the like and should not be applied to metal surfaces. Application and drying conditions must be at temperatures of 64°F or above and at a humidity of less than 65%. Increased air flow and/or drying temperatures will significantly decrease dry times.
If using conventional, HVLP, airless, or air assisted equipment, Recommended Tip Sizes if Spraying: conventional air 1.8 mm, HVLP 1.9-2.0 mm, airless 12-15 thousandths, air assisted airless 13-15 thousandths.
Pot Life: 24 hours (if catalyst is used-M702).
Mixing Ratio: Do Not Shake! This product should be catalyzed for maximum performance. Use M702 catalyst at 3 fluid ounces per gallon. Mix material thoroughly before and during use. Material may be mixed by hand or mechanical agitation at moderate speed.
Coverage: 431 Sq. Ft. per gallon at 1 mil dry film thickness.
Dry Time: Set to touch: 20 minutes, Dry to touch: 35 minutes, Dry to recoat: 2-3 hours. Always allow 2-3 hours between coats. Will achieve optimal hardness after 7 days.
Clean Up: Use water to clean all equipment when material is in a liquid stage. Use 2:1 mixture of water and Butyl Cellosolve (SOL-0061) to remove semi-dried coating. Use Acetone to remove dried coating. Dispose of in accordance with Federal, State, and Local regulation regarding pollution.
Care and cleaning of this finish: Use a mild dishwashing liquid and a damp cloth to remove food, grease, and other residue. Wipe dry. Do not use cleaners that contain ammonia, bleach, or abrasives as this may damage the finish.