My Cart
You have no items in your cart.
Please wait...
Please wait...
Address: 181 West Ave, Darien, CT 06820
Address: 9 Taylor Ave, Bethel, CT 06801
Address: 355 Newbury St, Boston, MA 02115
Address: 25 E Industrial Rd, Branford, CT 06405
Address: 59-67 Federal Rd, Danbury, CT 06810
Address: 1139 Post Rd, Fairfield, CT 06824
Address: 848 Lafayette Rd, Hampton, NH 03842
Address: 386 Smith Ridge Rd, South Salem, NY 10590
Address: 85 Bradley Rd, Madison, CT 06443
Address: 149 Everett St, Middleboro, MA 02346
Address: 1193 Ashley Blvd, New Bedford, MA 02745
Address: 308 S Frontage Rd, New London, CT 06320
Address: 140 Danbury Rd, New Milford, CT 06776
Address: 201 Merrimac St, Newburyport, MA 01950
Address: 50 Needham St, Newton Highlands, MA 02461
Address: 14 Church Hill Rd, Newtown, CT 06470
Address: 28 Hope St, Niantic, CT 06357
Address: 149 Westport Ave, Norwalk, CT 06851
Address: 131 Boston Post Rd, Orange, CT 06477
Address: 58 Shops at Five Way, Plymouth, MA 02360
Address: 1037 Forest Ave, Portland, ME 04103
Address: 620 Peverly Hill Road, Portsmouth, NH 03801
Address: 35 Scamman St, Saco, ME 04072
Address: 153 Ocean St, South Portland, ME 04106
Address: 87 Harvard Ave, Stamford, CT 06902
Address: 921 High Ridge Rd, Stamford, CT 06905
Address: 160 Avon St, Stratford, CT 06615
Phone:(203) 814-3050
Store hours:
Mon - Fri7am - 5pm
SatClosed
SunClosed
HolidaysClosed
Set as default storeAddress: 921 White Plains Rd, Trumbull, CT 06611
Address: 14 Warren St, Waltham, MA 02453
Address: 877 Post Rd E, Westport, CT 06880
Address: 669 Silas Deane Hwy, Wethersfield, CT 06109
Address: 129 Danbury Rd, Wilton, CT 06897
Address: 116 Cummings Park, Woburn, MA 01801
Address: 412 Route 1, Yarmouth, ME 04096
| Type | Interior/Exterior |
|---|---|
| Size | Quart |
| Color | Aluminum |
| Brand | Rust-Oleum |
| Series/Sub-Brand | Stops Rust® |
| Color Family | Gray |
| Finish | Gloss |
| Material | Oil-Based |
| Manufacturer Code | 7715502 |
Surface Preparation: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
Application: Before using, stir thoroughly to ensure any settled pigment is re-dispersed. If necessary, thin the material with acetone. For brush or roller, thinning is not normally required. For air spray, thin up to 15% with acetone. Do not thin with gasoline, lacquer thinner, turpentine, etc. For airless spray, thinning is not normally required. Apply with a good quality brush, roller or spray gun.Brush: Use light, even strokes. Excessive brushing reduces film thickness and protection.
Roller: Usa a 3/8 inch nap roller for rough surfaces. Cover approximately one square yard at a time. Roll away from previously coated area nd work back to it for a uniform appearance. Usa a brush on crevices and sharp edges.
Spray Gun: Follow spray gun direction carefully. Always keep the gun 10-12 inches away from the surface and in motion while spraying.
Recoat: Dry and recoat times are based on 70°F and 50% relative humidity. Allow more time at cooler temperatures. Dries to touch in 2-4 hours, to handle in 5-9 hours and is fully dry in 24 hours. Recoat after 24 hours. Do not apply Clear Enamel over Stops Rust Bright Coat FInish or Aluminum Finish.
Clean-Up: Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in home trash compactor.
