Old Masters, Spar-Marine Varnish, Exterior Oil-Based, Clear Semi-Gloss, Quart

Surface Preparation: All surfaces must be clean, dry, and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Bare Wood: Sand surface thoroughly with medium grit sandpaper and progress to fine grit sandpaper. Always sand in the direction of the wood grain. Remove dust with a tack rag. Previously Finished Surfaces: Surface should be sanded to remove imperfections and gloss, using extra fine sandpaper (220 grit) and, sanding with the grain. Remove dust with a tack rag. Stained Surfaces: Stain must be thoroughly dry before applying clear finish. Do not sand uncoated stained surface. Note: If a sealer is desired, we recommend Old Masters Penetrating Sealer. Application: tir thoroughly before and during application. DO NOT SHAKE. Do not apply in direct sunlight or areas of extreme air movement. Apply with pure bristle or polyester brush, flat pad, or spray. Apply in full, even coats. Flow on with minimum brushing to achieve a glass-like finish. Spar-Marine Varnish will dry to touch in 4 to 6 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Sand lightly between coats with fine sandpaper (220 grit) to produce a finer finish and promote adhesion. If sandpaper gums up, allow more dry time. Remove sanding dust. Reapply. For exterior surfaces, a minimum of three coats should be applied. Maintenance As with all exterior clear finishes, this product will not offer unlimited protection against the elements. Surfaces which receive direct sunlight may have to be re-coated annually to maintain gloss and to prevent cracking and peeling. Thinning Do not thin. Use as packaged. Coverage Approximately 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood. Drying Time Apply when air and surface temperatures are between 60° and 90°F and humidity is between 30% and 70%. At 50% relative humidity and 70°F, Spar-Marine Varnish will dry to touch in 6 to 8 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Drying time will be affected by temperature, humidity, and film thickness. Protect product from freezing prior to and during application. Wait 24 hours before subjecting surfaces to light use. Care should be used during the first week after application as the finish is curing to its ultimate hardness. Cleanup Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy. Surface Preparation: All surfaces must be clean, dry, and free from dirt, wax, grease, glue, and other contaminants or penetration and adhesion will be affected. Bare Wood: Sand surface thoroughly with medium grit sandpaper and progress to fine grit sandpaper. Always sand in the direction of the wood grain. Remove dust with a tack rag. Previously Finished Surfaces: Surface should be sanded to remove imperfections and gloss, using extra fine sandpaper (220 grit) and, sanding with the grain. Remove dust with a tack rag. Stained Surfaces: Stain must be thoroughly dry before applying clear finish. Do not sand uncoated stained surface. Note: If a sealer is desired, we recommend Old Masters Penetrating Sealer. Application: tir thoroughly before and during application. DO NOT SHAKE. Do not apply in direct sunlight or areas of extreme air movement. Apply with pure bristle or polyester brush, flat pad, or spray. Apply in full, even coats. Flow on with minimum brushing to achieve a glass-like finish. Spar-Marine Varnish will dry to touch in 4 to 6 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Sand lightly between coats with fine sandpaper (220 grit) to produce a finer finish and promote adhesion. If sandpaper gums up, allow more dry time. Remove sanding dust. Reapply. For exterior surfaces, a minimum of three coats should be applied. Maintenance As with all exterior clear finishes, this product will not offer unlimited protection against the elements. Surfaces which receive direct sunlight may have to be re-coated annually to maintain gloss and to prevent cracking and peeling. Thinning Do not thin. Use as packaged. Coverage Approximately 500 square feet per gallon. Coverage will vary significantly depending on application method and condition of wood. Drying Time Apply when air and surface temperatures are between 60° and 90°F and humidity is between 30% and 70%. At 50% relative humidity and 70°F, Spar-Marine Varnish will dry to touch in 6 to 8 hours. Under ideal drying conditions, allow 8 to 16 hours before recoating. Overnight drying is recommended. Drying time will be affected by temperature, humidity, and film thickness. Protect product from freezing prior to and during application. Wait 24 hours before subjecting surfaces to light use. Care should be used during the first week after application as the finish is curing to its ultimate hardness. Cleanup Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your local government agencies to ensure proper compliancy.